Adlink nanoX-BT Manuel d'utilisateur Page 24
- Page / 71
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Page 24 nanoX-BT
3.3.17. Serial Interface Signals
Signal Pin # Description I/O PU/PD Comment
SER0_TX A98 General purpose serial port transmitter (TTL level output) O CMOS Power rail tolerance 5V / 12V
SER0_RX A99 General purpose serial port receiver (TTL level input) I CMOS Power rail tolerance 5V / 12V
SER1_TX A101 General purpose serial port transmitter (TTL level output) O CMOS Power rail tolerance 5V / 12V
SER1_RX A102 General purpose serial port receiver (TTL level input) I CMOS Power rail tolerance 5V / 12V
3.3.18. Power And System Managemen
t
Signal Pin # Description I/O PU/PD Comment
PWRBTN# B12 Power button to bring system out of S5 (soft off), active on
falling edge.
I 3.3VSB PU 10k 3.3VSB
SYS_RESET# B49 Reset button input. Active low request for module to reset and
reboot. May be falling edge sensitive. For situations when
SYS_RESET# is not able to reestablish control of the system,
PWR_OK or a power cycle may be used.
I 3.3VSB PU 10k 3.3VSB
CB_RESET# B50 Reset output from module to Carrier Board. Active low. Issued
by module chipset and may result from a low SYS_RESET#
input, a low PWR_OK input, a VCC_12V power input that falls
below the minimum specification, a watchdog timeout, or may
be initiated by the module software.
O 3.3VSB
PWR_OK B24 Power OK from main power supply. A high value indicates
that the power is good. This signal can be used to hold off
Module startup to allow carrier based FPGAs or other
configurable devices time to be programmed.
I 3.3V PU 100k
3.3VSB
SUS_STAT# B18 Indicates imminent suspend operation; used to notify LPC
devices.
O 3.3VSB
SUS_S3# A15 Indicates system is in Suspend to RAM state. Active-low
output. An inverted copy of SUS_S3# on the carrier board
(also known as “PS_ON”) may be used to enable the non-
standby power on a typical ATX power supply.
O 3.3VSB
SUS_S4# A18 Indicates system is in Suspend to Disk state.
Active low output.
O 3.3VSB
SUS_S5# A24 Indicates system is in Soft Off state. O 3.3VSB Not supported,
connect to SUS_S4#
WAKE0# B66 PCI Express wake up signal. I 3.3VSB PU 10k 3.3VSB Not supported,
connected to WAKE1#
WAKE1# B67 General purpose wake up signal. May be used to implement
wake-up on PS/2 keyboard or mouse activity.
I 3.3VSB PU 10k 3.3VSB
BATLOW# A27 Battery low input. This signal may be driven low by external
circuitry to signal that the system battery is low, or may be
used to signal some other external power-management event.
I 3.3VSB PU 10k 3.3VSB
LID# A103 LID button. Low active signal used by the ACPI operating
system for a LID switch.
I OD 3.3VSB PU 10k 3.3VSB Emulate GPIO (BIOS)
SLEEP# B103 Sleep button. Low active signal used by the ACPI operating
system to bring the system to sleep state or to wake it up
again.
I OD 3.3VSB PU 10K 3.3VSB Emulated GPIO (BIOS)
- User’s Manual 1
- Revision History 2
- Preface 3
- Table of Contents 4
- 1. Introduction 8
- 2. Specifications 9
- 2.5. Video 10
- 2.6. Audio 10
- 2.7. LAN 10
- 2.8. Multi I/O and Storage 10
- 2.9. Power Specifications 10
- 2.10. Power Consumption 11
- 2.12. Environmental 11
- 2.14. Operating Systems 11
- Intel® Atom™ 12
- Intel® Celeron® 12
- “Baytrail” 12
- Side View 13
- All tolerances ± 0.05 mm 13
- Other tolerances ± 0.2 mm 13
- 3.1. AB Pin Definitions 14
- Row A Row B 15
- 3.3. AB Signal Description 18
- 3.3.3. DDI0 Channel 19
- 3.3.4. Gigabit Ethernet 19
- 3.3.5. SATA 20
- 3.3.6. PCI Express 20
- 3.3.7. Express Card 20
- 3.3.8. LPC Bus 21
- 3.3.9. USB 1.1/2.0 21
- 3.3.10. USB 3.0 Extension 22
- 3.3.12 22
- SPI (BIOS only) 22
- 3.3.13. Miscellaneous 23
- 3.3.14. SMBus 23
- 3.3.15. I2C Bus 23
- Page 24 nanoX-BT 24
- 3.3.19 25
- Power and Ground 25
- 4. Module interfaces 26
- 4.3. Status LEDs 28
- 4.4. XDP Debug Header 29
- 5.1.1. Voltages 31
- 5.1.2. Main Current 31
- 5.1.3. BMC Status 31
- 5.1.4. Exception Codes 32
- 5.1.5. BMC Flags 32
- 6. System Resources 33
- 6.3.1. PIC Mode 34
- 6.3.2. APIC Mode 34
- Page 36 nanoX-BT 36
- 6.6. SMBus Address Table 37
- 7. BIOS Setup 38
- 7.2. Main 39
- 7.2.6. System Management 40
- Page 42 nanoX-BT 42
- 7.3. Advanced 43
- 7.3.2. Memory 44
- 7.3.3. Graphics 44
- 7.3.4. SATA 45
- 7.3.5. USB 45
- 7.3.6. Network 46
- 7.3.7. PCI and PCIe 46
- 7.3.8. Super IO 48
- 7.3.10. Sound 49
- Page 50 nanoX-BT 50
- 7.3.12. Thermal 51
- 7.3.13. Miscellaneous 51
- 7.4. Boot 52
- 7.5. Security 54
- 7.6. Save & Exit 54
- 8.1. Checkpoint Ranges 56
- 8.2. Standard Checkpoints 56
- 8.2.2. SEC Beep Codes 57
- 8.2.3. PEI Phase 57
- Page 58 nanoX-BT 58
- 8.2.4. PEI Beep Codes 59
- 8.2.5. DXE Phase 59
- Page 60 nanoX-BT 60
- 8.2.6. DXE Beep Codes 62
- 8.2.7. ACPI/ASL Checkpoint 62
- 9. Mechanical Information 64
- 9.2. Thermal Solution 65
- 9.3. Mounting Methods 67
- 9.4. Standoff Types 68
- Safety Instructions 69
- Getting Service 70
Produits connexes et manuels pour Matériel Adlink nanoX-BT
Matériel Adlink LEC-BTS Manuel d'utilisateur
(22 pages)
(22 pages)
Matériel Adlink ETX-BT Manuel d'utilisateur
(70 pages)
(70 pages)
Matériel Adlink ETX-CV Manuel d'utilisateur
(86 pages)
(86 pages)
Matériel Adlink ETX-PVR Manuel d'utilisateur
(68 pages)
(68 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels