Adlink nanoX-BT Manuel d'utilisateur télécharger pdf (Page 65)

nanoX-BT Page 65

9.2. Thermal Solution

9.2.1. Heat Spreaders

The function of the heat spreader is to ensure an identical mechanical profile for all COM Express modules. By using a heat spreader, the

thermal solution that is built on top of the module is compatible with all COM Express modules.

9.2.2. Heat Sinks

A heat sink can be used as a thermal solution for a specific COM Express module and can have a fan or be fanless, depending on the

thermal requirements.

9.2.3. Installation

Install a heat spreader or heat sink using the following instructions.

Step 1: Place the COM Express module onto the connectors on the carrier board as shown.

Then press down on the module until it is firmly seated on the carrier board.

Step 2: Remove the protective membranes from the thermal pads.

1 2 ... 60 61 62 63 64 65 66 67 68 69 70 71

User’s Manual 1
Revision History 2
Preface 3
Table of Contents 4
1. Introduction 8
2. Specifications 9
2.5. Video 10
2.6. Audio 10
2.7. LAN 10
2.8. Multi I/O and Storage 10
2.9. Power Specifications 10
2.10. Power Consumption 11
2.12. Environmental 11
2.14. Operating Systems 11
Intel® Atom™ 12
Intel® Celeron® 12
“Baytrail” 12
Side View 13
All tolerances ± 0.05 mm 13
Other tolerances ± 0.2 mm 13
3.1. AB Pin Definitions 14
Row A Row B 15
3.3. AB Signal Description 18
3.3.3. DDI0 Channel 19
3.3.4. Gigabit Ethernet 19
3.3.5. SATA 20
3.3.6. PCI Express 20
3.3.7. Express Card 20
3.3.8. LPC Bus 21
3.3.9. USB 1.1/2.0 21
3.3.10. USB 3.0 Extension 22
3.3.12 22
SPI (BIOS only) 22
3.3.13. Miscellaneous 23
3.3.14. SMBus 23
3.3.15. I2C Bus 23
Page 24 nanoX-BT 24
3.3.19 25
Power and Ground 25
4. Module interfaces 26
4.3. Status LEDs 28
4.4. XDP Debug Header 29
5.1.1. Voltages 31
5.1.2. Main Current 31
5.1.3. BMC Status 31
5.1.4. Exception Codes 32
5.1.5. BMC Flags 32
6. System Resources 33
6.3.1. PIC Mode 34
6.3.2. APIC Mode 34
Page 36 nanoX-BT 36
6.6. SMBus Address Table 37
7. BIOS Setup 38
7.2. Main 39
7.2.6. System Management 40
Page 42 nanoX-BT 42
7.3. Advanced 43
7.3.2. Memory 44
7.3.3. Graphics 44
7.3.4. SATA 45
7.3.5. USB 45
7.3.6. Network 46
7.3.7. PCI and PCIe 46
7.3.8. Super IO 48
7.3.10. Sound 49
Page 50 nanoX-BT 50
7.3.12. Thermal 51
7.3.13. Miscellaneous 51
7.4. Boot 52
7.5. Security 54
7.6. Save & Exit 54
8.1. Checkpoint Ranges 56
8.2. Standard Checkpoints 56
8.2.2. SEC Beep Codes 57
8.2.3. PEI Phase 57
Page 58 nanoX-BT 58
8.2.4. PEI Beep Codes 59
8.2.5. DXE Phase 59
Page 60 nanoX-BT 60
8.2.6. DXE Beep Codes 62
8.2.7. ACPI/ASL Checkpoint 62
9. Mechanical Information 64
9.2. Thermal Solution 65
9.3. Mounting Methods 67
9.4. Standoff Types 68
Safety Instructions 69
Getting Service 70

Commentaires sur ces manuels

Pas de commentaire

Adlink nanoX-BT Manuel d'utilisateur Page 65

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Adlink nanoX-BT