Adlink PCI-8124-C Manuel d'utilisateur télécharger pdf (Page 83)

Function Library 73

6.7 FIFO Comparing

@ Name

@ Description

_8124_reset_fifo:

This function is used to reset (clear) the FIFO. The FIFO status

is return “Empty” status, when you issue this function.

_8124_get_fifo_sts:

This function is used to get the current FIFO status. There are

four status this function would return. The value meaning is as

below figure.

_8124_reset_fifo Reset FIFO data

_8124_get_fifo_sts Get the current FIFO status

_8124_set_fifo_data Set a comparing data to FIFO

_8124_set_fifo_array Set comparing data array to FIFO

_8124_set_fifo_shift Shift the FIFO data to comparator

_8124_set_fifo_level Set the FIFO low level

_8124_get_fifo_level Get the FIFO low level

1 2 ... 78 79 80 81 82 83 84 85 86 87 88 ... 101 102

User’s Manual 1
Getting Service from ADLINK 3
Table of Contents 5
Table of Contents iii 7
List of Tables 8
List of Figures 9
1 Introduction 11
2Introduction 12
1.1 Features 13
1.2 Specifications 14
Introduction 5 15
C - 70C 16
C - 80C 16
5%, 450mA(max) 16
5%, 100mA(max) 16
1.3 Supported Software 17
8Introduction 18
2 Installation 19
CN1: SCSI 50 pins Connector 20
CN2: TTL output 20
SW2: Default Trigger Level 20
2.3.1 Hardware Configuration 21
2.3.2 PCI Slot Selection 21
2.3.3 Installation Procedures 21
2.3.4 Troubleshooting: 21
12 Installation 22
2.5 CN1 Pin Assignments 23
2.8 Default Trigger Level 24
3 Signal Connections 25
7.5mA to 12.5mA 28
Signal Connections 21 31
3.5 TTL Input Ports 32
3.6 TTL Output Ports 33
24 Signal Connections 34
4 Operation Theory 35
4.1 Trigger Board Overview 36
Operation Theory 27 37
4.1.1 Encoder Channel 38
Operation Theory 29 39
4.1.2 Index Input (EZ) 40
4.1.3 Homing with EZ Signal 41
4.1.4 Trigger Pulse Width 41
4.1.5 Linear Function 41
4.1.6 FIFO 42
4.1.7 PWM & Mapping 42
4.1.8 Digital Filter 42
4.1.9 Trigger Counter 42
Operation Theory 33 43
4.2 Trigger Board Operation 44
4.2.2 Position Latch 45
4.2.3 Linear Function 45
4.2.4 FIFO Mode 46
4.2.5 Timer Function 46
4.4 Interrupt Control 48
Operation Theory 39 49
5 TriggerMaster Utility 51
5.3.1 Assign ID Type Dialog 52
5.3.2 Main Form 53
44 TriggerMaster Utility 54
TriggerMaster Utility 45 55
5.3.4 Sketch_of_setting Form 56
TriggerMaster Utility 47 57
5.3.6 Choose_PWM_Source Form 58
TriggerMaster Utility 49 59
5.3.8 Set_CNT_Source Form 60
5.3.9 Encoder_# Mode 61
52 TriggerMaster Utility 62
TriggerMaster Utility 53 63
54 TriggerMaster Utility 64
TriggerMaster Utility 55 65
56 TriggerMaster Utility 66
6 Function Library 67
System: Section 5.2 68
Comparator: Section 5.6 68
@ Description 71
@ Arguments 72
6.3 Encoder & Counter 73
 OFF (Rising edge) clear 75
6.4 PWM Configuration 76
0: Directionless 78
1: Count up 78
2: Count down 78
Function Library 71 81
6.6 Comparator 82
6.7 FIFO Comparing 83
 FIFO data > Empty 85
76 Function Library 86
6.8 Linear Comparing 87
0: disable, 1: enable 89
6.9 Manual Trigger 90
6.10 Digital Input 91
6.11 Latch 92
 ON (Falling edge) clear 93
6.12 Timer 94
Function Library 85 95
6.13 Interrupt 96
@ Syntax 100
@ Argument 100
Function Library 91 101
6.15 Return Errors 102

Commentaires sur ces manuels

Pas de commentaire

Adlink PCI-8124-C Manuel d'utilisateur Page 83

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Adlink PCI-8124-C