Adlink Express-LPC Manuel d'utilisateur Page 48
- Page / 86
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Express-LPC User’s ManualPage 48
SuperIO Configuration Screen
SuperIO configuration screen is a sub-menu of Onboard Device Configuration. You can use
this screen to select options for the Super IO settings. Use the up and down < Arrow >
keys to select an item. Use the < + > and < - > keys to change the value of the selected
option. The settings are described on the following pages. The screen is shown below. The
visibility of this SuperIO configuration screen depends on the presence of an onboard
SuperIO (Winbond W83627HF). If the Express-LPC is used on carrier w/o a SIO chip, the
legacy-free mode will take effect.
Floppy A
Use this field to specify options for the Floppy Configuration Settings.
Options: Disabled, 360 KB 5 ¼”, 1.2 MB 5 ¼”, 720 KB 3 ½”, 1.44 MB 3 ½”, 2.88 MB 3 ½”.
OnBoard Floppy Controller
This option enables/disables the Super IO’s floppy controller.
- Express-LPC 1
- Revision History 2
- Table of Contents 3
- Disclaimer 5
- Environmental Responsibility 5
- Trademarks 5
- Conventions 6
- 1 Introduction 7
- 2 Specifications 8
- 2.3 Audio 9
- 2.5 Multi I/O 9
- 2.7 Super I/O 9
- 2.8 Power Specifications 10
- 3 Functional Diagram 11
- 4 Mechanical Dimensions 12
- 5.1 COM Express 13
- Type 2 compatible pinout 13
- 5.3 Pin Definitions 14
- Pin Definitions (cont’d) 15
- 5.4 Signal Descriptions 16
- Signal Descriptions (cont’d) 17
- 6 Embedded Functions 25
- 6.2 GPIO 26
- 6.3 Hardware Monitoring 27
- 7 System Resources 28
- 7.3 Legacy I/O Map 29
- Legacy I/O Map (cont’d) 30
- PIC Mode 30
- APIC Mode 31
- 7.6 PCI Interrupt Routing Map 32
- 8 BIOS Setup Utility 33
- 8.1.1 Main Setup Menu 34
- 8.1.2 Navigation 35
- 8.2 Main Setup 37
- 8.3 Advanced BIOS Setup 38
- 8.3.1 CPU Configuration 39
- CPU Configuration Settings 39
- Max CPUID Value Limit 39
- 8.3.2 Chipset Configuration 41
- DRAM Frequency 41
- Configure DRAM Timing by SPD 41
- APIC ACPI SCI IRQ 41
- Internal Graphics Mode Select 42
- DVMT Mode Select 42
- 8.3.4 IDE Configuration 44
- IDE Configuration Settings 44
- ATA/IDE Configuration 44
- Legacy IDE Channels 44
- Hard Disk Write Protect 45
- IDE Detect Time Out 45
- ATA(PI)80Pin Cable Detection 45
- 8.3.5 AHCI Configuration 45
- AHCI Ports 46
- Onboard LAN Boot ROM 47
- HD Audio Controller 47
- SMBus Controller 47
- SuperIO Configuration Screen 48
- Floppy A 48
- OnBoard Floppy Controller 48
- Serial Port1 Address 49
- Serial Port2 Address 49
- Parallel Port Address 49
- Parallel Port Mode 49
- 8.3.7 USB Configuration 50
- USB Configuration Settings 50
- Parallel Port IRQ 50
- Active State Power-Management 53
- PCIE Ports 0-3 Configuration 53
- PCIE High Priority Port 53
- Remote Access 55
- Serial Port Number 55
- Remote Access Configuration 55
- Option Description 56
- 8.3.11 Trusted Computing 57
- Execute TPM Command 57
- 8.4 Power Management 58
- ACPI Aware O/S 59
- ACPI Version Features 59
- ACPI APIC Support 59
- USB Device Wakeup from S3/S4 59
- AMI OEMB Table 59
- Suspend mode 60
- Headless mode 60
- Restore on AC Power Loss 60
- ACPI OS Shutdown Mode 60
- Power Management/APM 61
- Power Button Mode 61
- Suspend Time Out 61
- 8.4.2 APM Configuration 61
- Video Power Down Mode 62
- Throttle Temperature 63
- Throttle Duty 63
- Critical Temperature 63
- 8.5 Boot Setup 64
- Quick Boot 65
- Quiet Boot 65
- AddOn ROM Display Mode 65
- Bootup Num-Lock 66
- PS/2 Mouse Support 66
- Wait for ‘F1’ If Error 66
- Hit ‘DEL’ Message Display 66
- Interrupt 19 Capture 66
- Boot Device Priority 67
- Boot Device Groups 67
- 8.6 Security Setup 68
- 8.6.3 Change User Password 70
- 8.6.4 Clear User Password 70
- 8.7 Exit Menu 71
- Discard Changes 72
- Load Optimal Defaults 72
- Load Failsafe Defaults 72
- Viewing BIOS Checkpoints 73
- 9.3 POST Code Checkpoints 76
- POST Code Checkpoints cont’d: 77
- 9.5 DIM Code Checkpoints 78
- 9.6 ACPI Runtime Checkpoints 79
- 9.7 Boot Block Beep Codes 80
- 9.8 POST BIOS Beep Codes 80
- Important Safety Instructions 82
- Getting Service 84
Produits connexes et manuels pour Matériel Adlink Express-LPC
Matériel Adlink LEC-BTS Manuel d'utilisateur
(22 pages)
(22 pages)
Matériel Adlink ETX-BT Manuel d'utilisateur
(70 pages)
(70 pages)
Matériel Adlink ETX-CV Manuel d'utilisateur
(86 pages)
(86 pages)
Matériel Adlink ETX-PVR Manuel d'utilisateur
(68 pages)
(68 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels