Adlink cExpress-BT2 Manuel d'utilisateur télécharger pdf (Page 71)

cExpress-BT2 Page 71

Step 3: Assemble the heatsink onto the COM Express module.

Use the four M2.5, L=6mm screws provided to fasten the heatsink to the module.

Step 4: Place the COM Express module and heatsink assembly onto the connectors on the carrier board as shown.

Then press down on the module until it is firmly seated on the carrier board.

Step 5: Use the five M2.5, L=16mm screws provided to secure the COM Express module to the carrier board from the solder side.

1 2 ... 66 67 68 69 70 71 72 73 74 75 76 77

User’s Manual 1
Revision History 2
Preface 3
Table of Contents 4
1. Introduction 8
2. Specifications 9
2.5. Video 10
2.6. Audio 10
2.7. LAN 10
2.8. Multi I/O and Storage 10
2.16. Functional Diagram 12
Other tolerances ± 0.2 mm 13
Top View 13
Side View 13
All Ø tolerances ± 0.05 mm 13
Row A Row B Row C Row D 14
3.3. AB Signal Descriptions 18
3.3.4. Gigabit Ethernet 19
3.3.5. SATA 19
3.3.6. PCI Express 20
3.3.7. Express Card 21
3.3.8. LPC bus 21
3.3.9. USB 21
3.3.11. SPI (BIOS only) 22
3.3.12. Miscellaneous 23
3.3.13. SMBus 23
3.3.14. I2C Bus 23
Page 24 cExpress-BT2 24
3.3.18. Power and Ground 25
3.4. CD Signal Descriptions 26
3.4.4. Power and Ground 28
4. Module interfaces 29
4.3. Status LEDs 31
XDP Debug Header 32
4.5. Fan Connector 32
5.1.1. Voltages 35
5.1.2. Main Current 35
5.1.3. BMC Status 35
5.1.4. Exception Codes 36
5.1.5. BMC Flags 36
6. System Resources 37
6.3.1. PIC Mode 38
6.3.2. APIC Mode 39
Page 40 cExpress-BT2 40
DIMM A A0h 41
DIMM B A4h 41
BMC 50h 41
Extend GPIO 40h 41
7. BIOS Setup 42
7.2. Main 43
7.2.6. System Management 44
7.3. Advanced 47
7.3.2. Memory 48
7.3.3. Graphics 48
7.3.4. SATA 49
7.3.5. USB 49
7.3.6. Network 50
7.3.7. PCI and PCIe 51
7.3.8. Super IO 53
7.3.10. Sound 54
7.3.12. Thermal 55
7.3.13. Miscellaneous 56
7.4. Boot 57
Page 58 cExpress-BT2 58
7.5. Security 59
7.6. Save & Exit 59
8.1. Checkpoint Ranges 61
8.2. Standard Checkpoints 61
8.2.2. SEC Beep Codes 62
8.2.3. PEI Phase 62
8.2.4. PEI Beep Codes 64
8.2.5. DXE Phase 64
Page 66 cExpress-BT2 66
8.2.6. DXE Beep Codes 67
8.2.7. ACPI/ASL Checkpoint 67
Page 68 cExpress-BT2 68
9. Mechanical Information 69
9.2. Thermal Solution 70
Page 72 cExpress-BT2 72
9.3. Mounting Methods 73
9.4. Standoff Types 74
Safety Instructions 75
Getting Service 76

Commentaires sur ces manuels

Pas de commentaire

Adlink cExpress-BT2 Manuel d'utilisateur Page 71

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Adlink cExpress-BT2