Adlink STC-15W04 Manuel d'utilisateur

Advance Technologies; Automate the World.Manual Rev.: 0.20 PreliminaryRevision Date: Dec. 26, 2014Part No: 50-1Z201-1000STC-15W04 Smart Touch Compu

xList of TablesThis page intentionally left blank.

Introduction 1STC-15W041 Introduction1.1 OverviewThe STC series of Smart Touch Computers is designed for indus-trial automation and other application

2Introduction1.3 Package ContentsPlease check that your package contains the items below. If youdiscover damaged or missing items, please contact your

Introduction 3STC-15W041.4 Block DiagramFigure 1-1: STC-15W04 Block DiagramD2550NM10Realtek 8111ERealtek 8111EDDR3 1067MT/sSingle ChannelSingle Chan

4Introduction1.5 Mechanical DimensionsFigure 1-2: STC-15W04 DimensionsDimensions in mm407.3262.3233.5378.567.2

System Description 5STC-15W042 System Description2.1 SpecificationsDisplayDisplay Size 15.6”Resolution 1366x768 pixelsBrightness 300 nits (w/o touchs

6System DescriptionTable 2-1: Specifications2.2 I/O Panel LayoutBottom ViewFigure 2-1: STC-15W04 Rear I/O LayoutRear ViewPowerInput Voltage24VDC ±15%

System Description 7STC-15W042.3 Pin DefinitionsRJ-45 Gigabit Ethernet ConnectorsTable 2-2: RJ-45 GbE Pin DefinitionsTable 2-3: LAN LED Status Defin

8System DescriptionUSB ConnectorTable 2-4: USB 2.0 Port PinoutRS-485 Port (isolated)Table 2-5: RS-485 Port PinoutPin # Signal Name1Vcc2UV0-3UV0+4GND

System Description 9STC-15W04CFast SocketTable 2-6: CFast Socket Pin DefinitionPin # Signal NameGround S1SATA_TX-P S2SATA_TX-N S3Ground S4SATA_RX-N S

ii Revision HistoryRevision HistoryRevision Release Date Description of Change(s)0.10 8/12/2014 Preliminary release0.20 26/12/2014Remove driver instal

10 System DescriptionDC Power Input ConnectorTable 2-7: DC Power Input PinoutPin # Signal1Vin-2 Earth Ground3Vin+Pin 1

Getting Started 11STC-15W043 Getting Started3.1 Panel MountingThe STC-15W04 can be panel mounted using the 10 bracketsincluded with the device. Make

12 Getting Started5. Hand-tighten the mounting brackets with a Phillips-headscrewdriver to secure it to the panel. Do not overtightenthe brackets to a

Getting Started 13STC-15W043.2 Connecting PowerInsert the positive and negative leads from the power supply asmarked on the chassis into the pluggabl

14 Getting Started3.3 CFast Card InstallationTo install or remove the CFast card, loosen the captive screw untilit is possible to remove the CFast slo

Getting Started 15STC-15W043.4 CMOS Battery ReplacementTo change the CMOS backup battery, loosen the captive screwuntil it is possible to remove the

16 Getting StartedReplace the CMOS battery with one of the same type (CR2450). Replace the slot cover and tighten the scew.

BIOS 19STC-15W044 BIOS4.1 IntroductionThe following chapter describes basic navigation for the AMI EFIBIOS setup utility.4.2 Starting the BIOSTo ente

20 BIOSSetup MenuThe main BIOS setup menu is the first screen that you can navi-gate. Each main BIOS setup menu option is described in thisuser’s guid

BIOS 21STC-15W04The < F8 > key on your keyboard is the Fail-Safe key. It is not dis-played on the key legend by default. To set the Fail-Safe s

Preface iiiSTC-15W04PrefaceCopyright 2014 ADLINK Technology Inc.This document contains proprietary information protected by copy-right. All rights ar

22 BIOSF2 The < F2 > key on your keyboard is the previous values key. It is not displayed on the key legend by default. To set the previous valu

BIOS 23STC-15W04Press the < Enter > key to save the configuration and exit. You can also use the < Arrow > key to select Cancel and then

24 BIOS4.3 Main SetupWhen you first enter the Setup Utility, you will enter the Main setupscreen. You can always return to the Main setup screen by se

BIOS 25STC-15W044.4 Advanced BIOS SetupSelect the Advanced tab from the setup screen to enter theAdvanced BIOS Setup screen. You can select any of th

26 BIOS4.4.1 PCI Subsystem SettingsPCI Latency TimerValue to be programmed into PCI Latency Timer Register.Options: 32 PCI Bus Clocks, 64 PCI Bus Cloc

BIOS 27STC-15W04PERR# GenerationEnables or Disables PCI Device to Generate PERR#. Set thisvalue to Disabled, EnabledSERR# GenerationEnables or Disabl

28 BIOSTechnology) and disable for other OS (OS not optimized forHyper-Threading Technology.Execute Disable BitExecute Disable Bit can prevent certain

BIOS 29STC-15W044.4.3 Thermal ConfigurationCPU Thermal ConfigurationDTS SMMDisabled: ACPI thermal management uses EC reported tem-perature values. En

30 BIOSPlatform Thermal ConfigurationCritical Trip PointThis value controls the temperature of the ACPI Critical TripPoint - the point at which the OS

BIOS 31STC-15W04Passive Trip PointThis value controls the temperature of the ACPI Passive TripPoint - the point in which the OS will begin throttling

iv PrefaceConventionsTake note of the following conventions used throughout thismanual to make sure that users perform certain tasks andinstructions p

32 BIOS4.4.4 IDE ConfigurationSATA Controller(s)Enable/Disable SATA Device.Configure SATA asSelect a configuration for the SATA Controller. Set this v

BIOS 33STC-15W04SATA Port 0 Hot PlugDesignates this port as Hot Pluggable. Set this value to Dis-abled, Enabled.SATA Port 1Enable or Disable the SATA

34 BIOS4.4.5 USB ConfigurationLegacy USB SupportEnables legacy USB support. Auto option disables legacy sup-port if no USB devices are connected. Disa

BIOS 35STC-15W04Device power-up delayMaximum time the device will take before it properly reportsitself to the Host Controller. 'Auto' uses

36 BIOS4.4.6 Super IO ConfigurationSerial Port 1 ConfigurationSet Parameters of Serial Port 1 (COM A). Options: Enabled/Disabled. A sample screen is s

BIOS 37STC-15W04Change SettingsThis option specifies the base I/O port address and interruptrequest address. Set this value to below screen options:

38 BIOS4.4.7 IT8781F Hardware Monitor

BIOS 39STC-15W044.4.8 PPM ConfigurationEISTEnable/Disable Intel SpeedStep. Set this value to Disabled,Enabled.CPU C state ReportEnable/Disable CPU C

40 BIOSC4 Exit TimingThis option controls a programmable time for the CPU voltageto stabilize when exiting from a C4 state. Set this value toDefault,

BIOS 41STC-15W044.5 Chipset ConfigurationSelect the Chipset tab from the setup screen to enter the ChipsetBIOS Setup screen. You can select any of Ch

Table of Contents vSTC-15W04Table of ContentsRevision History... iiPreface...

42 BIOS4.5.1 Host Bridge ConfiguratioMRC Fast BootEnable or disable MRC fast boot. Set this value to Disabled,Enabled.Max TOLUDMaximum Value of TOLUD.

BIOS 43STC-15W04Panel ScalingSelect the LCD panel scaling option used by the InternalGraphics Device. Set this value to Auto, Force Scaling, Off,Main

44 BIOS4.5.2 South Bridge ConfigurationRestore AC Power LossSelect AC power state when power is re-applied after a powerfailure. Set this value to Pow

BIOS 45STC-15W04UHCI #3 (ports 4 and 5)Control the USB UHCI (USB 1.1) functions. Disable from high-est to lowest controller. Set this value to Disabl

46 BIOS4.6 Boot SettingsSetup Prompt Timeout Set this number of seconds to wait for setup activation key.1~65535 (0xFFFF) means indefinite waiting.Boo

BIOS 47STC-15W04Quiet Boot X Disabled - Set this value to allow the computer system to display the POST messages.X Enabled - Set this value to allow

48 BIOSInterrupt 19 CaptureAllows option ROM to trap Int 19. Options: Enabled/Disabled.CSM SupportEnable, Disable CSM Support. If Auto is selected, ba

BIOS 49STC-15W044.7 Security SetupAdministrator, User PasswordIf only the administrator's password is set, then this only limitsaccess to setup

50 BIOS4.8 Save & Exit MenuSelect the Save & Exit tab from the setup screen to enter the Save& Exit BIOS Setup screen. You can display an

BIOS 51STC-15W04Discard Changes and Exit Exit system setup without saving any changes.Save Changes and ResetReset the system after saving the changes

vi Table of Contents4.4.1 PCI Subsystem Settings... 264.4.2 CPU Configuration...

52 BIOSDiscard ChangesDiscard changes done so far to any of the setup options.Restore DefaultsRestore/Load Defaults values for all the setup options.S

BIOS 53STC-15W04Launch EFI Shell from file system deviceAttempts to Launch EFI Shell application (Shell.efi) from one ofthe available file system dev

54 BIOSThis page intentionally left blank.

Important Safety Instructions 55STC-15W04Important Safety InstructionsFor user safety, please read and follow all instructions,WARNINGS, CAUTIONS, an

56 Important Safety InstructionsA Lithium-type battery may be provided for backup power.X Never attempt to fix the equipment. Equipment should only be

Getting Service 57STC-15W04Getting ServiceContact us should you require any service or assistance. ADLINK Technology, Inc. Address: 9F, No.166 Jia

58 Getting ServiceADLINK Technology, Inc. (French Liaison Office) Address: 6 allée de Londres, Immeuble Ceylan 91940 Les Ulis, France Tel: +33

List of Figures viiSTC-15W04List of FiguresFigure 1-1: STC-15W04 Block Diagram... 3Figure 1-2: STC-15W04 Di

viii List of FiguresThis page intentionally left blank.

List of Tables ixSTC-15W04List of TablesTable 2-1: Specifications.................. 6Table 2-2: RJ