Adlink XMC-E540 Manuel d'utilisateur

Advance Technologies; Automate the World.Manual Rev.: 2.00Revision Date: August 7, 2013Part No: 50-1Z124-1000XMC-E540Dual-port 10GBASE-T Ethernet X

xList of FiguresThis page intentionally left blank.

List of Tables xiXMC-E540List of TablesTable 2-1: XMC-E540 Power Consumption... 7Table 3-1: RJ-45 10GbE Connector

xii List of TablesThis page intentionally left blank.

Introduction 1XMC-E5401 Introduction1.1 OverviewThe XMC-E540 is a dual-port 10GBASE-T Ethernet XMC modulewith equipped with an Inte® Ethernet Control

2Introduction1.3 Block DiagramFigure 1-1: XMC-E540 Functional Block DiagramPCIe x1 / x2 / x4 / x8 MDI0 MDI1 Intel X540

Introduction 3XMC-E5401.4 Package Contents The XMC-E540 is packaged with the following components. If anyof the items on the contents list are missin

4IntroductionThis page intentionally left blank.

Specifications 5XMC-E5402 Specifications2.1 XMC-E540 ModuleStandards VITA 42.3-2006 XMC PCI Express Protocol Layer StandardForm Factor • IEEE P1386,

6 Specifications2.2 Intel® Ethernet Controller X540-AT2The following section describes the features and functions ofIntel® Ethernet Controller X540-AT

Specifications 7XMC-E5402.3 Power ConsumptionThe power consumption data of the XMC-E540 was measuredinstalled in an ADLINK cPCI-6510 carrier blade us

ii Revision HistoryRevision HistoryRevision Release Date Description of Change(s)2.00 2013/08/07 Initial release

8 SpecificationsThis page intentionally left blank.

Board Interfaces 9XMC-E5403 Board InterfacesThis chapter illustrates the board layout, connector pinassignments, and switch settings to familiarize u

10 Board Interfaces3.2 Connector Pin AssignmentsRJ-45 10G Ethernet Connectors (CN2/3)Table 3-1: RJ-45 10GbE Connector Pin DefinitionsPin # 100BASE-TX

Board Interfaces 11XMC-E540XMC Connector (CN1)Table 3-2: XMC Connector Pin DefinitionPin# A B C D E F1 PET0p0 PET0n0 3.3V PET0p1 PET0n1 VPWR2 GND GND

12 Board InterfacesThis page intentionally left blank.

Getting Started 13XMC-E5404 Getting Started4.1 Installing the Module1. Remove the XMC slot filler faceplate from the front panelof the host board.2.

14 Getting Started4.2 Driver InstallationThe XMC-E540 drivers can be found on the ADLINK All-In-OneDVD at X:\XMC\XMC-E540\LAN, or at the ADLINK websit

Important Safety Instructions 15XMC-E540Important Safety InstructionsFor user safety, please read and follow all instructions,WARNINGS, CAUTIONS, an

16 Important Safety InstructionsX Never attempt to fix the equipment. Equipment should only be serviced by qualified personnel.A Lithium-type battery

Getting Service 17XMC-E540Getting ServiceContact us should you require any service or assistance. ADLINK Technology, Inc. Address: 9F, No.166 Jian

Preface iiiXMC-E540PrefaceCopyright 2013 ADLINK Technology, Inc.This document contains proprietary information protected by copy-right. All rights ar

18 Getting ServiceADLINK Technology, Inc. (French Liaison Office) Address: 15 rue Emile Baudot, 91300 Massy CEDEX, France Tel: +33 (0) 1 60 12 3

iv PrefaceUsing this ManualAudience and ScopeThe XMC-E540 User’s Manual is intended for hardwaretechnicians and systems operators with knowledge of in

Preface vXMC-E540ConventionsTake note of the following conventions used throughout thismanual to make sure that users perform certain tasks andinstru

vi PrefaceThis page intentionally left blank.

viiXMC-E540Table of ContentsRevision History... iiPreface...

viiiThis page intentionally left blank.

List of Figures ixXMC-E540List of FiguresFigure 1-1: XMC-E540 Functional Block Diagram ........ 2Figure 3-1: XMC-E540 Board Layo